• 1 Answer SOURCE: This is a reply I received from Taylor customer support. I have followed this procedure enough times to wear out the original battery and still get the Err 1 message. You may have better luck. Thank you for your e-mail. The reboot below may clear the error from your scale.

The scale is specially designed to test your body weight, body fat, hydration, muscle and bone percentages and to help you keep a close eye on the daily changes of your body fat, hydration, muscle, bone and weight. Windows Xp Pro Sp3 Hp Oem Download here. Based on the analysis of your height, weight, age, etc., it calculates your daily energy requirement, and can.

You may need to do this several times to completely reboot the system. Please let us know if you have any questions or continue to display the Error.

Remove the battery from the scale 2. Set the scale on the floor without the battery in place. Stand on the scale for 10 seconds (still without the battery) 4.

Carefully replace the battery without turning the scale on. Using only one foot, tap the scale or apply just enough pressure to turn on the display. (It should show dashes or zero's) IMMEDIATELY REMOVE YOUR FOOT. Let the scale turn off 7. Step on the scale for a weight reading Regards, Linda DLT Consumer Relations Taylor Precision Products & Salter Housewares 2220 Entrada del Sol, Suite A Las Cruces, NM 88001 Toll free - 800-289-0944 866-843-3905 Direct - 575-526-0944 ext 3172 Posted on Jun 24, 2009. • 39 Answers SOURCE: From the Taylor Site Here are the basic ERR messages and their meanings: • Error 0: Initialization • Error 1: Instability (scale is on an uneven surface ex: carpet) • Error 2: Unit may have been jarred or unit was overloaded (customer went over the maximum weight capacity) • Error 3: Contact error (Feet were not wet for Body fat reading, feet aren’t big enough to reach sensors) • Error 4: Body fat is out of range • Error 5: Water is out of range I got an ERR2 message and now the scale doesn’t work.

What should I do? The following reset procedure is used when the scale shows an err2, err, 0.0, inaccurate weight, or some other unusual error. • Remove the battery from the scale. • Sit the scale on a hard surface floor. • Step up onto the scale, stand still for about 5 seconds and step off the scale. • Re-install your battery. • Place the scale back on a hard surface floor.

• With one foot only, place just enough weight on the scale for the display shows zero’s or dashes. Once you see zeros or dashes remove your foot. • Wait for the scale to turn off again. • Step up onto the scale for a weight.

If the reset is successful, you should receive a weight right away. If you continue to receive one of the error messages above please call our Customer Service department or via email. You can also try the reset procedure a 2nd time. Sometimes the reset procedure will work the second time. Tamil Mashup Mp3 Songs Free Download 2014. Posted on Jan 21, 2010. • 1 Answer SOURCE: My scale was fine the other day. I weighed myself earlier in the day.

I tried to weigh myself later in the day and the scale started reading ERR1. I called Taylor and they had me try to 'reset' the scale twice. It did not work. From the Taylor Site Here are the basic ERR messages and their meanings: • Error 0: Initialization • Error 1: Instability (scale is on an uneven surface ex: carpet) • Error 2: Unit may have been jarred or unit was overloaded (customer went over the maximum weight capacity) • Error 3: Contact error (Feet were not wet for Body fat reading, feet aren’t big enough to reach sensors) • Error 4: Body fat is out of range • Error 5: Water is out of range I got an ERR2 message and now the scale doesn’t work. What should I do? The following reset procedure is used when the scale shows an err2, err, 0.0, inaccurate weight, or some other unusual error.

• Remove the battery from the scale. • Sit the scale on a hard surface floor. • Step up onto the scale, stand still for about 5 seconds and step off the scale. • Re-install your battery.

• Place the scale back on a hard surface floor. • With one foot only, place just enough weight on the scale for the display shows zero’s or dashes. Once you see zeros or dashes remove your foot. • Wait for the scale to turn off again. • Step up onto the scale for a weight. If the reset is successful, you should receive a weight right away.

If you continue to receive one of the error messages above please call our Customer Service department or via email. You can also try the reset procedure a 2nd time. Sometimes the reset procedure will work the second time.

Jan 15, 2010 . This is a reply I received from Taylor customer support. I have followed this procedure enough times to wear out the original battery and still get the Err 1 message. You may have better luck.

Thank you for your e-mail. The reboot below may clear the error from your scale. You may need to do this several times to completely reboot the system.